数字图象信号的电缆传输

结合强力输送带横向断裂预报检测系统，介绍一种数字图象信号电缆异步传输的具体实现方法，它满足某些工业检测和控制系统的远地数字信号传输的要求。内容包括多路数据信号合成与分解，信号的编码、解码和识别再生三部分主要硬件电路的设计思想。最后给出了传输实验结果     

激光光纤准直系统的试验研究

介绍一种新的激光准直系统,该系统通过单模光纤建立新的光发射基准,从而有效地抑制了由于激光腔热变形而产生的光束漂移。另外,该系统采用了标量卡尔曼数字滤波器耒降低大气扰动和其他环境因素对测量的影响,在2.5m的测量范围内,系统稳定性可以控制在±1.5μm以下。该系统适用于作为形状误差和运动误差测量时的直线基准。     

基于F-P腔的激光频率稳定传递方法

量子传感的发展需要频率高度稳定的激光器为基础,且实现大失谐激光频率稳定通常是提高其精度和灵敏度的关键。针对大失谐激光稳频问题,提出了一种利用法布里-珀罗（F-P）腔传递激光频率稳定性的方法。以饱和吸收稳频法锁定的激光器频率为参考,基于锁相原理,锁定F-P腔长度。利用F-P腔长度这个稳定的参考点,实现目标激光器的频率的精确锁定。实验将目标激光器波长锁定于767.001 nm,失谐频率为150 GHz,锁定后的频率漂移为1 MHz/h。该方法解决了激光大失谐稳频问题,对工程实践和科学研究有重要意义。      

基于数字孪生的智能脉动管控

为提升飞机总装脉动生产线智能化水平,开展了基于数字孪生的智能脉动管控研究。基于数字孪生五维模型理论构建了飞机总装脉动生产线数字孪生应用架构,从反应式计划调度、物流精准配送、智能作业指导、产线健康监视、资源迭代优化配置5个方面开展了技术研究,为复杂产品装配的智能制造应用提供参考。     

Measurement of mass diffusion coefficients of O_2 in aviation fuel through digital holographic interferometry

The experimental apparatus to measure the mass diffusion coefficients of O2 in aviation fuel was constructed based on the digital holographic interferometry method. The theory of mass diffusion coefficient and interference image processing were introduced in detail. The accuracy of the experiment was verified by measuring the mass diffusion coefficient of 0.33 mol/L KCl in aqueous solution at 298.15 K. The mass diffusion coefficients of O_2 in RP3 and RP5 aviation fuels were measured at temperature from 278.15 K to 333.15 K, and the Arrhenius equation was employed to fit the experimental data. In terms of the Stokes-Einstein equation, the viscosities of these two aviation fuels were tested to estimate the correlation among mass diffusion coefficient, viscosity and temperature. A uniform polynomial calculation correlation was proposed to predict the mass diffusion coefficients of O_2 in both RP3 and RP5 aviation fuels, and its accuracy is considerably higher than that of the Stokes-Einstein equation.     

Numerical study of traveling ionosphere disturbances with vertical incidence data

High frequency ionosphere vertical sounding, as an important and representative application for detecting the ionosphere and studying the characteristics of radio propagation, can be utilized to monitor the ionosphere continuously variation and to acquire the ionosphere asymmetrical features of diverse scale above the ionosphere vertical sounding stations. This is a first article on real time application of numerical methods to obtain the parameters of traveling ionosphere disturbances (TIDs) using vertical incident ionograms. In this paper, the distribution of ionosphere electron density with TIDs is constructed using a background ionosphere model superimposed a perturbation theory model. The background ionosphere electron density is modelled by the inversion of vertical incident ionograms which are observed before the appearance of the disturbance. Based on the fourth order Adams-Bashforth-Moulton (the so-called ABM) predictor corrector method, instead of Runge-Kutta method, the fast digital ray tracing method is established. According to process of the disturbed trace simulation and parameters inversion, the characteristic parameters of ionosphere disturbance at different detection time can be obtained in real time. The numerical analysis of TIDs is then captured completely.     

A novel architecture of electro-hydrostatic actuator with digital distribution

To address the flow imbalance rapidly of the asymmetric Electro-Hydrostatic Actuator (EHA), this paper presents a novel architecture of asymmetric EHA with the Digital Distribution (EHA-DD). It also improves the flow nonlinearity and control accuracy of the pump, especially in the low-speed condition. The digital distribution with two High-Speed on–off Valves (HSVs) not only balances flow instead of the check valves, but also replaces the pump at the low-speed to control output flow by adjusting the PWM signal. The pump and HSVs are the crucial components to control flow output. Firstly, the flow calculation models of the pump and the duty ratio inversed model of the HSV are obtained through experimental tests and the identification method. To get the control input signal for the required flow, the pump speed and PWM duty ratio for the HSVs are inversed to compensate for flow output. Further, a multimode digital flow distribution control method based on pump speed, mainly including the pump-controlled mode for large flow demand and valve-controlled mode for little flow demand, is proposed to control the accurate flow output actively. The step extension experiments based on the flow calculation models are conducted on the EHA-DD prototype under elastic, opposite varying load. The results demonstrate that the EHA-DD realizes little position error by accurate flow control, and it is also beneficial to improve the service life of the pump.     

合理运用SI技术快速收敛高速数字电路设计

随着数字电路集成度和工作频率的不断提高,信号完整性(Signal Integrity, SI)问题在产品研制过程中越来越突出。以惯导系统中的某导航计算机为例,针对故障信号回路,使用仿真软件对其SDRAM时钟信号进行信号完整性仿真,并进行优化设计。通过对比优化前和优化后的仿真与测量结果,验证了由于端接参数不匹配造成SDRAM时钟信号的非单调性畸变问题。仿真与测量结果表明,在产品研制流程中加入信号完整性仿真环节有利于设计快速收敛,提前规避风险,缩短研发周期,降低设计成本,提高电路产品的可靠性和电磁兼容性。     

某框基于后置程序逆向设计及数字化高效加工研究

介绍了飞机某框从逆向设计到数字化高效加工详细流程,应用以CATIA V5、VERICUT为代表的先进数字化制造技术,使零件数字化设计、数字化加工、工艺流程得到全面改进,为今后零件逆向设计及数字化加工奠定良好的基础。     

Bayesian network-based extraction of lunar impact craters from optical images and DEM data

Impact craters are among the most noticeable geomorphological features on the planetary surface and yield significant information about terrain evolution and the history of the solar system. Thus, the recognition of impact craters is an important branch of modern planetary studies. Aiming at addressing problems associated with the insufficient and inaccurate detection of lunar impact craters, a decision fusion method within the Bayesian network (BN) framework is developed in this paper to handle multi-source information from both optical images and associated digital elevation model (DEM) data. First, we implement the edge-based method for efficiently searching crater candidates which are the image patches that can potentially contain impact craters. Secondly, the multi-source representations of an impact crater derived from both optical images and DEM data are proposed and constructed to quantitatively describe the two-dimensional (2D) and three-dimensional (3D) morphology, consisting of Histogram of Oriented Gradient (HOG), Histogram of Multi-scale Slope (HMS) and Histogram of Multi-scale Aspect (HMA). Finally, a BN-based framework integrates the multi-source representations of impact craters, which can provide reductant and complementary information, for distinguishing craters from non-craters. To evaluate the effectiveness and robustness of the proposed method, experiments were conducted on three lunar scenes using both orthoimages from the Lunar Reconnaissance Orbiter (LRO) and DEM data acquired by the Lunar Orbiter Laser Altimeter (LOLA). Experimental results demonstrate that integrating optical images with DEM data significantly decreases the number of false positives compared with using optical images alone, with F₁-score of 84.8% on average. Moreover, compared with other existing fusion methods, our proposed method was quite advantageous especially for the detection of small-scale craters with diameters less than 1000 m.